ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
           º                                                     º
           º       Compex USB To Fast Ethernet LAN Adapter       º
           º            CopyRight(c) 2001 Compex Inc.            º
           º                 All rights reserved                 º
           º                                                     º
           ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

	Support model: LinkPort/UE202-B only
		      
 		
  -----------------
  BEFORE YOU BEGIN
  -----------------
  Your computer must meet the following requirements to be compatible
  with Compex USB Fast Ethernet Adapters:

  1.  In order to use this device, you must have a copy of Microsoft
      Windows 2000 operating system installed on your PC or notebook.

  2.  Also, the device requires that a USB port is installed and
      enabled on your PC or notebook. Some PCs have a USB port, but it
      is disabled. Usually there is a toggle switch on the motherboard
      that will enable a PC's USB port. Consult your computer's user guide.
      Some motherboards have USB interfaces, but no ports. You should be
      able to install your own USB port and attach it to your PC's
      motherboard using hardware purchased at any computer store.

 Please refer to A:\README.TXT for latest update not documented in the manual.

  ----------------------------------------------------------------------------
  DRIVER INSTALLATION
  ----------------------------------------------------------------------------
  Follow the instructions below to install the adapter's driver.

  1.  Install the Compex USB Fast Ethernet Adapter to your
      PC or notebook or USB hub if you haven't already done so.
      (See A:\README.TXT in Hardware setup)

  2.  Turn ON your PC or notebook and boot up Windows 2000.

  3.  Windows 2000 will display,

       "USB 10/100 LAN"

      in "New Hardware Found" dialog box and "Add New Hardware Wizard"
      dialog box.
      If the Wizard does not appear, please refer the section "Is USB
      port device correctly installed" below.

  4.  Click "Next" button when "Search for the best for your device.
      [Recommended]" is on.

  5.  Insert the USB Adapter Driver Diskette in your floppy drive.

  6.  Enable the "Floppy disk drives" check box and then click "Next"
      button.

  7.  Windows 2000 will display,

        "Compex LinkPort/UE202-B USB To Fast Ethernet Adapter"

      in "Add New Hardware Wizard" dialog box.

  8.  Click "Next" button and Windows starts to copy files from Windows
      2000 CD-ROM to your hard disk.

  9.  When the Insert Disk message appears, click OK. When the Copying Files
      ... window appears, type A:\ into the box displayed and click OK.

 10.  Click "Finish" button from "Add New Hardware Wizard" dialog box.

 11.  Remove the USB Adapter Driver Diskette from your floppy drive.

 12.  Restart Windows and it is now ready for networking.

  
  Is USB port device correctly installed ?
  ----------------------------------------
  If the Wizard does not appear when you plug in the adapter, go to
  "Device Manager" to check whether "Universal Serial Bus controllers"
  exists. You can do this to go to "Device Manager" :

  Right click on the "My Computer" icon on your desktop, then select
  "Properties" or Double click on the "System" icon in Control Panel.
  Select the "Device Manager" tab. Select and expand "Universal
  Serial Bus controllers".  For example, you will see

  Universal Serial Bus controllers
    Intel 82371AB/EB PCI to USB Universal Host Controller
    USB Root Hub

  Make sure that there is no red "X" sign or "!" mark on them.
  Thus, USB is correctly installed.