________________________________________________________________ | | | Compex RE100ATX 10/100 PCI Fast Ethernet Adapter | | (C) Copyright PDS, 2002. All Rights Reserved. | |______________________________________________________________| How to install RE100ATX-PCI adapter to SCO OpenServer 5.0 ========================================================= *NOTE: This driver is compatible with RE100ATX and RE100TX 1) Copy the setup file to the root of SCO Unix hard disk. e.g. cd / doscp D:/sco/setup . 2) Change Setup file to executable. e.g. chmod +x setup 3) Run setup e.g. ./setup Install Compex RE100ATX 10/100 PCI Fast Ethernet Adapter Driver. Please input source path ? ( ex: D:/sco/5.x) Type, D:/sco and press Enter key and message below display. Please wait to transfer files ................ Transfer End ............ 4) Execute "custom" A menu selection screen will be popped up. Using [->] key to move cursor to "Software" menu item then press [] key to get into pull down menu then move to "Install New..." then press [ENTER] key ----------- Begin Installation on scoopen ---------- | | | What host (machine) do you want to install from? | | | | --------------------------------------------------| | ³<*> From scoopen | | ³< > From another host | |---------------------------------------------------| | | | [ Continue ] [ Cancel ] [ Help] | ----------------------------------------------------| Select From scoopen and use [TAB] key to move cursor to [ Continue ] then press [ENTER] key and press [] key to get into pull down menu ------------ Select Media --------------------- | | | Insert media, and select media device. | |---------------------------------------------| | | | Media Device: Media Image | | ------------------------- | | | Floppy Disk Driver 0 | | | | *Media Images | | | ------------------------- | |---------------------------------------------| | [ Continue ] [ Help ] | ----------------------------------------------- -> Select "Media Image" and use [TAB] key to move cursor to [ Continue ] then press [ENTER] key then press [ENTER] key again ---------------------- Install Reference on scosysv ---------------------- | | | Installing: Compex RE100ATX 10/100Base-TX PCI Fast Ethernet Adapter | | | | Do you want a FULL or PARTIAL installation? | | | |------------------------------------------------------------------------| | [ Full ] [ Partial ] [ Cancel ] [ Help ] -------------------------------------------------------------------------- Using [TAB] key to move cursor to [ Full ] then press [ENTER] key After the installation progress the following message is displayed ------------ Question ---------- | Installation complete | |-------------------------------| | [ OK ] | |-------------------------------| Press [Enter] key and the selected adapter, Compex RE100TX 10/100Base-TX PCI Fast Ethernet is added to the package list Using [<-] key to move cursor back to "Host" menu item then press [] key to get into pull down menu then move to "Exit" then press [ENTER] key Now that the driver is installed in the system successfully. 4) Execute "netconfig" to configure the driver A menu selection screen will be popped up. At "Hardware" menu item press [] key to get into pull down menu then move to "Add new LAN adapter" then press [ENTER] key --------------------------- Add new LAN adapter ----------------------------- | Following adapters have been found: | |---------------------------------------------------------------------------| | Compex RE100TX 10/100Base-TX PCI Fast Ethernet adapter -PCI Bus#0, PCI# | | | | | |---------------------------------------------------------------------------| |[ Configure hardware not listed above... ] | |---------------------------------------------------------------------------| |[ Continue ] [ Cancel ] [ Help ] | |---------------------------------------------------------------------------- Use the Tab key to move to [Continue] and then press [ENTER] key. -------------------------------- Add Protocol -------------------------------- |Select one networking product to be added to: | | | |Compex RE100TX 10/100Base-TX PCI Fast Ethernet Adapter: | |----------------------------------------------------------------------------| | HW Compex RE100ATX 10/100Base-TX PCI Fast Ethernet Adapter | | - SCO IPX/SPX | | * - SCO TCP/IP | | | |----------------------------------------------------------------------------| | [ Add ] [ Cancel ] [ Help ] | ------------------------------------------------------------------------------ Using [] key to move cursor to "SCO TCP/IP" then press [ENTER] key. ----------------- SCO TCP/IP Configuration --------------- º | º Local Host Name: |scoopen_____________| [ Advanced ]| º IP Address: |192.168.0.100_______| Options... | º Netmask: |255.255.255.0_______| | ºBroadcast Address: |192.168.0.255_______| | º Domain Name: |scoopen.com_________| | º TCP connections: |256_________________| | º Pseudo ttys: |32__________________| | º | |---------------------------------------------------------| | [ OK ] [ Cancel ] [ Help ] | |---------------------------------------------------------| * Note:- the values above are just examples. Contact your administrator for the proper information for your network. Input the required information then use [TAB] key to move cursor to "OK" then press [ENTER] key. ----------------------------- Message ----------------------------------------- | The following products were successfully configured into the system | | SCO TCP/IP | | Compex RE100TX 10/100Base-TX PCI Fast Ethernet Adapter - PCI Bus#0,PCI Device| | | |------------------------------------------------------------------------------| |[ OK ] [ Help ] | |------------------------------------------------------------------------------| Press [ENTER] key At "Hardware" menu item press [] key to get into pull down menu then move to "Exit" then press [ENTER] key ------------------------ Question -------------------------- | The Unix Kernel must be re-linked before the changes | | made here will have an effect. | | Do you want to re-link the kernel now? | |----------------------------------------------------------| | [ YES ] [ NO ] | |----------------------------------------------------------| Press [ENTER] key Do you want this kernel to boot by default (y/n) y Do you want the kernel environment rebuilt (y/n) y 5) Reboot unix # shutdown -y -g0 6) On rebooting, Compex RE100ATX 10/100Base-TX PCI Fast Ethernet adapter will be initialized. Press Control-D to startup the server. Compex RE100ATX 10/100Base-TX PCI Fast Ethernet adapter is now ready to service the network. ------------------------